1
/
of
4
Auto Parts Tokyo
Speed Display Meter Brixton Granville 250x2020 Motorcycle 1-6 Level Gear Indicator Digital Gear Meter Bike Digital Display
Speed Display Meter Brixton Granville 250x2020 Motorcycle 1-6 Level Gear Indicator Digital Gear Meter Bike Digital Display
Regular price
$172.00 USD
Regular price
Sale price
$172.00 USD
Unit price
/
per
Shipping calculated at checkout.
Condition: New
Couldn't load pickup availability
Motorcycle Gear Indicator for Brixton Granville 250 X 2020 Function: This is a gear indicator display assembly that can accurately display the current gear number. The motorcycle gear indicator has a good display effect, small and beautiful design. Instalación: Medidor de velocidad de la pantalla de la motocicleta el proceso de instalación es simple, práctico y fácil de usar. Con perfecta adaptabilidad, sólo tiene que sustituir y montar. Maquina antes de comprar.
Bienvenido a nuestra tienda y le deseamos una agradable experiencia de compra.somos fabricantes profesionales de piezas de motocicletas.Para cualquier pregunta o inquietud, no dude en ponerse en contacto con nuestro equipo de servicio al cliente. Features: Light Color: Red/Blue/Green 1-6 Levels IP68 Waterproof Gear Display Fixtures: Brixton Granville 250 you may need to use a small flat head screwdriver to separate them). With the ignition on, rotate the rear wheels. The speedometer should read 0. If so, turn off the ignition and proceed to the next step. Otherwise, if the speedometer registers a non-zero speed, you did not disconnect the correct coupler and should look again. 2. After separating the speed sensor connector, plug in both the male and female 3-pole Jefizz hip harness connectors. Make sure the connector is fully seated. 3. Locate the RPM/timing sensor (pickup) connector. The sensor is mounted on the top or side of the crankcase. Follow the cable from the sensor until you find the 3-prong connector. Here are the connector locations for some common models: Monster S4RS: Behind the left side cover under the seat. ST3: On the right side of the engine, zipped to the frame. 4. Pull the large rubber boot back from the plug to disconnect the connector and leave the three wires exposed. 5. Thread the black/green wire from Jefy's Hips through the rubber boot from the back. Make sure the wires do not touch the exhaust pipe or cylinder block. 6. Using the supplied red wire tap connector, connect the Jefy's Hip Black/Green wire to the wire in connector slot position 1. Instructions: Place the unstripped running wire (slot position 1) into the running channel. Close the side cover until it clicks. Cut the excess length and fully insert the unstripped tap wire (black/green) and check the position. Insert the blade (U-Contact) and press down with finger pressure. Then push the U contact all the way in with pliers.
Manufacturer: MUTYNE
Part number: MUTYNE
Item weight: 150 g
Packing size: 3 x 2 x 1 cm; 150 g
Size: One Size
br>Color: Red
Quantity: 1
Bienvenido a nuestra tienda y le deseamos una agradable experiencia de compra.somos fabricantes profesionales de piezas de motocicletas.Para cualquier pregunta o inquietud, no dude en ponerse en contacto con nuestro equipo de servicio al cliente. Features: Light Color: Red/Blue/Green 1-6 Levels IP68 Waterproof Gear Display Fixtures: Brixton Granville 250 you may need to use a small flat head screwdriver to separate them). With the ignition on, rotate the rear wheels. The speedometer should read 0. If so, turn off the ignition and proceed to the next step. Otherwise, if the speedometer registers a non-zero speed, you did not disconnect the correct coupler and should look again. 2. After separating the speed sensor connector, plug in both the male and female 3-pole Jefizz hip harness connectors. Make sure the connector is fully seated. 3. Locate the RPM/timing sensor (pickup) connector. The sensor is mounted on the top or side of the crankcase. Follow the cable from the sensor until you find the 3-prong connector. Here are the connector locations for some common models: Monster S4RS: Behind the left side cover under the seat. ST3: On the right side of the engine, zipped to the frame. 4. Pull the large rubber boot back from the plug to disconnect the connector and leave the three wires exposed. 5. Thread the black/green wire from Jefy's Hips through the rubber boot from the back. Make sure the wires do not touch the exhaust pipe or cylinder block. 6. Using the supplied red wire tap connector, connect the Jefy's Hip Black/Green wire to the wire in connector slot position 1. Instructions: Place the unstripped running wire (slot position 1) into the running channel. Close the side cover until it clicks. Cut the excess length and fully insert the unstripped tap wire (black/green) and check the position. Insert the blade (U-Contact) and press down with finger pressure. Then push the U contact all the way in with pliers.
Manufacturer: MUTYNE
Part number: MUTYNE
Item weight: 150 g
Packing size: 3 x 2 x 1 cm; 150 g
Size: One Size
br>Color: Red
Quantity: 1
Share
